Contrary to what many people believe, wood as a building material is not static and perfect. While some types of wood are more stable than others, each type has its own unique characteristics. If a carpenter fails to adequately deal with these characteristics, then some woodworking problems would occur. There are so many woodworking hints and tips to choose from, and this article looks at a few of the most helpful ones.
The first tip is about is about the importance of table saw safety. When cross cutting on top of a table saw, the cut length should be set with a block clamped to the fence. The fence should never be used directly in order to avoid a board getting kicked right back at the worker.
Alternatively, a wood block should be clamped in front of the blade to the fence. This will make the board end free from that fence in the course of the cut and as soon as it is finished. For instance, if the carpenter makes an exactly one inch block, they can set scale of the fence one inch bigger than the desired length.
Another tip involves use of tape to gather excess glue. In order to prevent stains resulting from oozing glue along the joints, the work pieces can be held together with no glue. All that is required is putting some tape onto the joint, and then cutting along it with the use of a sharp blade. The work pieces are separated, glue applied and then clamped again together. The glue used will splatter on the tape and not on the wood, and before it dries the tape is peeled.
Use of a stair gauge is the other guideline. Stair gauges are mainly used as crosscut guides as well as for laying out stair jacks. They are fixed to carpenters square whereby they will be helpful in marking notches. However, it is when using circular saw that this will give the best results, if they are both set on a single square tongue.
A carpenter can achieve more accuracy by using a drafting square. When an accurate square is needed in the range of between two and three feet, there are limited options. Drywall squares are usually cumbersome and inaccurate. Using carpenter squares involves the nagging hassle of hooking them onto a work piece edge. Drafting squares are quite accurate and the carpenter will find himself using it nearly as often as he uses a tape measure.
Hot glue is capable of sticking wood much better than clamps. In case woodworkers have to finish, file, shape, sand or file something tiny, reaching for a hot glue gun and then sticking the piece onto a pedestal stick is recommended. Hot glue is as good as any clamp when it comes to holding things. It can also be popped loose with the use of putty knives when the work finished. Caution should however be taken not to use too much force or the wood will be torn out or the piece broken.
The above woodworking hints can be of help to any carpenter. There are tens of other tips, but those discussed above are the main ones that will make woodworking much easier.
The first tip is about is about the importance of table saw safety. When cross cutting on top of a table saw, the cut length should be set with a block clamped to the fence. The fence should never be used directly in order to avoid a board getting kicked right back at the worker.
Alternatively, a wood block should be clamped in front of the blade to the fence. This will make the board end free from that fence in the course of the cut and as soon as it is finished. For instance, if the carpenter makes an exactly one inch block, they can set scale of the fence one inch bigger than the desired length.
Another tip involves use of tape to gather excess glue. In order to prevent stains resulting from oozing glue along the joints, the work pieces can be held together with no glue. All that is required is putting some tape onto the joint, and then cutting along it with the use of a sharp blade. The work pieces are separated, glue applied and then clamped again together. The glue used will splatter on the tape and not on the wood, and before it dries the tape is peeled.
Use of a stair gauge is the other guideline. Stair gauges are mainly used as crosscut guides as well as for laying out stair jacks. They are fixed to carpenters square whereby they will be helpful in marking notches. However, it is when using circular saw that this will give the best results, if they are both set on a single square tongue.
A carpenter can achieve more accuracy by using a drafting square. When an accurate square is needed in the range of between two and three feet, there are limited options. Drywall squares are usually cumbersome and inaccurate. Using carpenter squares involves the nagging hassle of hooking them onto a work piece edge. Drafting squares are quite accurate and the carpenter will find himself using it nearly as often as he uses a tape measure.
Hot glue is capable of sticking wood much better than clamps. In case woodworkers have to finish, file, shape, sand or file something tiny, reaching for a hot glue gun and then sticking the piece onto a pedestal stick is recommended. Hot glue is as good as any clamp when it comes to holding things. It can also be popped loose with the use of putty knives when the work finished. Caution should however be taken not to use too much force or the wood will be torn out or the piece broken.
The above woodworking hints can be of help to any carpenter. There are tens of other tips, but those discussed above are the main ones that will make woodworking much easier.
About the Author:
If you are in search of a great online source for woodworking hints, click thewoodworkersshop.com. For more details on the Wood Workers Shop visit us at http://thewoodworkersshop.com today.
No comments:
Post a Comment